Last Updated on September 17, 2022
If you want to disassemble a SKS rifle, this article will help you get started. We’ll cover how to remove the bolt, extractor, and gas piston. You can even learn how to remove the barrel! After reading this article, you should be able to disassemble any SKS rifle with relative ease. Hopefully, this guide has been helpful. And remember, if you have any questions or concerns, don’t hesitate to contact us!
Disassemble a SKS rifle
There are a few things you should know before you start disassembling your SKS rifle bolt. Remember that firearms are dangerous, so you should always treat them as such. In addition to storing them safely, remember to keep them away from children, as the wrong handling can cause the gun to accidentally discharge and cause injury or damage to your property. This article is for reference only, and Ken Kraushaar Firearms assumes no liability in the dissemination of this information.
First, you need to unclip the SKS rifle’s firing pin. You can do this by unscrewing the retainer pin and pulling out from the back of the bolt. Once you’ve removed the firing pin, push the extractor out of the bolt by pressing it toward the end. You should hear a pop as you release the spring. After you’ve disconnected the bolt, clean it and reassemble it.
Once you have removed the rear sight block, locate the retaining pin. This pin is attached to the rear sight block. Rotate the lever to the right until the spring extends outward. The bolt and carrier are now separated from the bolt. Then, lift the rear sight block assembly out of the rifle. You’ll find the locking lever on the right side. It usually rotates 45 degrees above and below the horizontal.
Now, you’ll have to remove the recoil spring and curly section from the rear of the bolt carrier. Remove the C clip and slide the bolt assembly rearward along the rails. The bolt will be in two halves, with the upper half acting as the blowback piston while the lower half contains the firing pin. Once you’ve done this, the bolt can be disassembled in two halves, with the recoil spring and firing pin remaining on the lower half.
Remove the bolt
To disassemble an SKS, disassemble the bolt and firing pin. While you may not need to remove the bolt if you only need to clean it, removing the bolt is an important step if you intend to clean the firing pin. The bolt is made of metal so it may be difficult to remove the firing pin with the bolt in place. To remove the bolt, carefully push the bolt toward the end of the barrel and pivot away from it. To clean the bolt and firing pin, gently unscrew the firing pin and cleaning the bolt with Simple Green is the best way to proceed.
If you find that the firing pin is loose, you may want to take it out of the rifle and replace it. However, this may not improve the accuracy of the SKS rifle. If this is the case, you can fix the loose receiver by using acraglass. Follow the instructions on the acraglass packet to make sure it is installed correctly. If the barrel is corroded, you may want to consider re-crowning it. This process adds a slight roll to the edge of the barrel that allows gases to escape. Re-crowning your barrel will improve accuracy by increasing the accuracy of the rifle.
Remove the gas piston
To remove the gas piston from the SKS bolt, locate the right-hand side of the gun and find the lever that holds the gas piston in place. The lever is similar to the one at the back of the gun, and it must be rotated in order to release the gas piston. This lever may be difficult to rotate, but you can use a screw driver to force it to rotate. After removing the gas piston, you can reassemble the SKS.
The gas piston is driven onto the tappet, which is a spring loaded short rod that delivers the WHAP to the bolt carrier. If the gas piston is damaged, you should replace it with a new one. The same is true if you need to replace the hand guard. Some gun owners will want to remove the hand guard for cleaning purposes, but they may be unable to do so themselves. In such cases, they will need the assistance of a machine shop.
The gas piston extension is located in the front of the rear sight block and is connected to a powerful spring. When the pin is pushed out, the locking lever is pushed out and the spring expands. You can then set the spring aside. The remaining parts are reassembled. To replace the handguard, you can remove the wooden handguard and replace it with a new one. You can also attach a new handguard to the SKS bolt.
When removing the gas piston from the SKS bolt, you should first remove the bolt and then the gas tube. The gas tube assembly is made up of several parts, and the standard gas tube is divided into two pieces. The piston tube has a larger internal diameter than the rod tube. This allows the gas piston to slide into the piston tube. The rod portion of the gas piston is press-fitted into the piston tube.
Remove the extractor
To remove the extractor from a SKS bolt, turn the bolt nose so that it is pointed to the right. Then, remove the firing pin carrier and extractor. The firing pin should protrude about 40-60 millimeters from the bolt face. Next, remove the extractor spring. This spring is made of braided wire and is easy to spot. Once you have removed the extractor, you can reconnect the firing pin tip.
To remove the extractor, first unscrew the retaining pin from the firing pin. Then, use a hammer to push it out of the bolt. Note that you may need a vice to hold the bolt in place while removing the extractor. Once the firing pin is out, you may need to remove the bolt. This will help you remove the firing pin. This is a relatively simple procedure, but it requires some skills and patience.
First, unscrew the metal dust cover of the SKS bolt. You should notice a spring cover on the right side. It will be under pressure from the spring. After unscrewing the dust cover, you can now pull the bolt carrier out of the bolt. Next, unscrew the retaining pin and the spring cover. Then, pull the bolt carrier out by turning the bolt back toward the bolt’s opening.
Remove the firing pin
To remove the firing pin from a Sks bolt, first make sure that the tyros are not bent. Also, make sure that you return the firing pin in the proper upright position. There are many different ways to do this, but one of the most common is to turn it upside down. This method may cause damage to the bolt or firing pin. There are also several different patterns of firing pins, so you need to be careful not to damage the bolt.
The firing pin can be found in the upper assembly of the bolt. Remove the retainer pin, then gently push the firing pin out of the bolt. You may need to use a hammer or a screwdriver to pry the pin loose. Once the pin is free, you can reassemble the bolt. This will require a bit of strength and patience, so it’s best to take your time.
After you’ve removed the retaining pin, remove the bolt. A soft mallet will be needed to press the firing pin and spring assembly out of the bolt. Once this is done, the new firing pin should protrude slightly from the front of the bolt. Using pressure, press the new firing pin into the bolt. Be careful not to damage the bolt during the procedure. This way, you can prevent the firing pin from accidentally discharging.
When working with Sks bolts, you can try to break the rust bond that holds the firing pin to the channel. You can also try tapping the firing pin to loosen it. Be careful not to damage the firing pin while removing the retaining pin. Just make sure to be careful and follow the instructions carefully. If you’re not familiar with the procedure, you can try some easy tips below.
About The Author
Mindy Vu is a part time shoe model and professional mum. She loves to cook and has been proclaimed the best cook in the world by her friends and family. She adores her pet dog Twinkie, and is happily married to her books.