Last Updated on September 17, 2022
You may not be able to open the hood of your Jeep Grand Cherokee if you do not know how to open it. To open the hood, you will have to release the hood latches. These latches are located under the drivers side of the instrument panel, slightly off-center to the right. The warning below must be followed precisely or you could cause serious injury or even death.
Changing the hood latch
Changing the hood latch on a 2017 Jeep Grand Cherokee is easy. First, remove the hood release cable. This cable is held in place by two clips on the hood. Unhook the latch from the bell crank by pulling the cable through the firewall. Attach the new hood release cable through the hole in the firewall and attach it with two screws. If you can’t open the hood, you can replace the cable by removing the kick panel and connecting it to the hood release cable.
To remove the rear hatch latch, you need to crawl inside the hatch area. If you are not comfortable with crawling into the vehicle, you can use an arm or a screwdriver to pull the latch. Next, unbolt the latch from the door. You may need to use a rivet gun to do this. You can also use a wrench or a screwdriver to remove the latch.
To remove the hood latch on your 2017 Jeep Grand Cherokee, locate the release mechanism. It is located to the left of the steering wheel, under the dash panel. Locate the black release lever with a picture of a lifted hood. Pull it towards you to release the latch. If you can’t locate it, look for a plastic piece on the floor. Pull the lever toward you until it is released.
After you locate the hood release lever, locate the second hood release on your Jeep Cherokee. If the hood latch has become stuck, you can try to release it manually by pressing the lever several times. If that doesn’t work, take the vehicle to a mechanic. Most mechanics will repair this problem. If you are unable to open the hood, it may be because the hood release lever is not properly installed.
Checking the air filter
One of the most overlooked preventative maintenance steps for your vehicle is to check the air filter. Dirty air filters will prevent the engine from running as efficiently as it should. You can check the air filter by opening the hood and checking the cover underneath. A dirty filter will need to be replaced. Another important component to check is the coolant level. Your Jeep’s coolant reservoir is located on the driver’s side of the engine compartment. If this is low, your engine will overheat and lose power.
If the cabin air filter is dirty or is damaged, you can replace it easily. These parts are relatively inexpensive and easily available online. It is a good idea to buy several air filters and swap them when they become dirty. Depending on the size of the filter, it may be a good idea to replace it with a new one. Checking the air filter when opening the hood of a Jeep Grand Cherokee should not be too difficult.
To access the air filter, raise the hood and remove the fuel tank cap. Next, remove the air filter housing. There are many fasteners around this part of the engine. Use the right tool to remove the plastic housing. Once removed, replace the filter housing with a new one. After removing the old one, make sure the markings on the new filter match with the old one.
Another common issue that affects the engine is a dying oil pump. A dying oil pump can damage other components in the engine. This could make the repair even more expensive if the driver continues to use the vehicle. In such a case, the air filter should be changed as soon as possible. Checking the air filter when opening the hood of a Jeep Grand Cherokee will save you money in the long run.
Checking the battery
When opening the hood of your Jeep Grand Cherokee, you should first check the battery. The battery in your car is typically on the left side, but in a Jeep Grand Cherokee it is in the front. It is normally rectangular, and has a minus and plus terminal. You should make sure the battery is not discharged if you find that it is. If it is, you may need to replace the battery.
After connecting the positive terminal to the positive terminal of the battery, you should check the voltage on the voltmeter. The voltmeter should read fifteen to thirteen volts. If it is under twelve volts, the battery may need to be recharged or replaced. This test is not difficult and only takes a few minutes. You can check the battery yourself in your Jeep Grand Cherokee if you are familiar with car maintenance.
If the voltage on your Jeep Grand Cherokee doesn’t look right, you should replace it. The battery in your Jeep Grand Cherokee should last three to five years, but the life of a battery depends on the type, size and mileage. For this reason, it’s important to check your battery every so often. If you aren’t sure where the battery is, consult your Jeep Grand Cherokee’s owner’s manual to determine where it’s located.
If you find that the battery in your Jeep Grand Cherokee is dead, you can try Jump-starting it. A dead battery will not allow the car’s centralized locking system to operate. You can access the interior of the vehicle by opening the trunk. However, you must be aware that your Jeep Grand Cherokee may have a “hidden” trunk lock. Before jumping the battery, make sure you follow these steps:
To visually inspect the battery, open the hood. You should make sure the terminals are not corroded. Clean them with a wire brush if necessary. If the battery is older than three years, it’s time to replace it. Also, check the air filter. This is located in the engine compartment, on the driver’s side. A dirty air filter can cause a variety of problems in the engine, including decreased power and fuel efficiency.
Checking the fuse
If you’re opening the hood of your Jeep Grand Cherokee and find the fuse panel is empty, you may be experiencing a variety of problems. If your headlights or taillights aren’t working, you may be liable to get pulled over and fined EUR 135 for not having working headlights. The first place to look is the fuse panel. If you can’t find the fuse panel, try looking for it in your vehicle’s owner’s manual or on the manufacturer’s website.
First, locate the fuse box in the engine compartment. It’s located on the driver’s side of the engine compartment. Pull off the cover, then open the fuse box and check the metal strip inside to determine whether it’s blown. If it is, replace it with a new one with the same amperage rating. If the fuse is blown, the electrical system may be tripped and the engine will not start.
If your Jeep’s IOD is too high or too low, you’ll want to change it. To do this, simply remove the fuse housing top by unscrewing the retaining ring. Afterward, you’ll want to disconnect the negative battery cable, then remove the tabs on either side of the opening. If the fuse isn’t blown, it will be rated as low and you can safely replace it.
Another important step to perform when opening the hood of your Jeep Grand Cherokee is to check the blower motor resistor. This component is located behind the glove box, and is white and rectangular in shape. It measures about three inches long. If the blower motor is malfunctioning, a blown fuse may be the culprit. Also, check the fuse for short circuits in the engine compartment.
Another important part of your Jeep Grand Cherokee is the windshield washer system. If the pump isn’t working, the fuse might be blown or the wiring harness is broken. In addition to the blown fuse, you should also check the electrical connector. If it is, connect a multimeter to the connector and check for 12 volts. If it’s not, the pump needs replacing.
About The Author
Mindy Vu is a part time shoe model and professional mum. She loves to cook and has been proclaimed the best cook in the world by her friends and family. She adores her pet dog Twinkie, and is happily married to her books.