If you’re new to building things for RC boats, you may wonder how to make a rc boat base stand. Well, it’s actually quite simple – just use some PVC plumbing pipe, a base board, and some Styrofoam blocks. There are a number of other materials you can use as well. Listed below are some of the most common ones.
PVC plumbing pipe
You can build a stand for your RC boat using PVC plumbing pipe by following the steps below. First, you will need to measure your boat. Measure the height from the lowest point to the highest point of its hull, then divide that number by two. Next, measure the width of your boat, then add it to the first number. The length of the pipe you need will be determined by the width of your boat plus the length of the pipe you have cut.
Start by cutting a long PVC pipe into four pieces. The long PVC pipe will be used as a base for the RC boat. Make sure to seal the ends of the two shorter pieces. Next, you will need to cut one more piece to form the stern. Use the remaining pieces to form the rest of the boat’s hull. Once this is complete, glue the PVC pieces together. Then, place the metal frame over the PVC hull.
Next, mark the PVC pipes using a compass. You need a pipe with a diameter of 1/2 inch, and you will need six caps. You will also need ten Ts and four elbows. You can find PVC pipe in the tool aisle of most chain stores, and you can cut the plywood to fit your model. Lastly, add a few pipe outriggers and a wood platform to hold your boat.
The frame of your stand is a critical piece of equipment. A poorly constructed boat stand can cause damage to the boat, spectators, or both. A sturdy, well-designed stand will prevent pressure points and ensure the proper support of the hull. The last thing you need is a cheap, flimsy stand. You can save a lot of money by buying a ready-made one, but you should also take into consideration the safety aspects.
Styrofoam blocks
If you are looking for a cheap and easy way to make a boat stand for your model, consider using surplus plastic foam packing blocks. These foam blocks are used to ship fragile and electronic items in boxes, and can be obtained almost anywhere for next to nothing. Unlike Styrofoam blocks, these plastic packing blocks are not commonly found in stores or warehouses. The process is quick and easy, and it will allow you to spend more time constructing your boat.
First, cut the foam blocks to fit the size of your boat’s base. This measurement will determine the width and length of the transom. Then, stack the blocks to create a tall base. Once the base is tall enough, glue the blocks together and you have a rc boat stand! The boat can then be put on top! Now, it’s time to test out the boat stand.
Cut the Styrofoam blocks to fit the size of your model. Cut them into a rectangular shape using a common bread knife. This will give you the base that you need for your model. Then, use masking tape or cling-film to secure them. Once the foam is dry, place the model on top of the base and enjoy your new stand.
Next, use the Styrofoam blocks to make the hull. It is best to use closed-cell construction foam. This type of foam is inexpensive, easy to find, and works well. You can also use a hacksaw blade for this purpose. The finished model should be easy to put together and the styrofoam will be nearly half-dissolved.
Wood
Before you start building a boat stand, you’ll need some materials. You’ll need some threaded metal pipe and a welding kit. The boat stand’s base must be shaped to fit the shape of the hull and transom. The “vee” should be narrower at the bow end than at the stern. You may need to make several cuts to achieve the proper shape.
To stabilize the hull of a boat, build a simple pipe stand. It should support about half the length of the boat. Stack the bunks under the hull’s strakes, or outside. This will prevent the boat from rolling on the stand. Catamarans and hydros use bunks inside the sponsons to support the tunnel. Riggers typically use narrower bunks with a padded crosspiece.
Once you’ve decided on the size of the base, cut foam blocks to the desired height. You can also use foam blocks that are rectangular in shape. The base should be wide enough to support the boat. Make sure to measure the height of your hull and running hardware before you begin cutting the wood. This step will save you a lot of time later on. If you’d prefer a different wood type for your boat stand, consider purchasing an extra-large foam block.
When choosing your materials, take into account the varying demands of your r/c boat. Buying tools can be expensive, but they’re necessary if you want to build a high-quality wooden stand. Most people already have a small set of hand tools, but you’ll still need some hobby tools to build a wood RC boat stand. There are even a few “short kits” available.
Plastic foam packing blocks
If you want to build your own stand for your RC boat, you need to know how to cut plastic foam packing blocks into the correct shape. You can cut each block into a rectangle by using a knife with a serrated edge, such as a bread knife. This will give you a base that has two layers at the front, middle and rear. The blocks will add the necessary height for your boat’s hull.
First, you’ll need to measure your boat’s hull and determine how long and wide it should be. If you want to have a tall base for your boat, you can stack the blocks to make it taller. Once you’ve measured the dimensions of your boat, you can start cutting the foam blocks. Make sure to use enough foam to cover the base, but don’t overdo it!
The process of building a boat stand from scratch can be time-consuming and difficult. Plastic foam packing blocks are the easiest way to build a custom boat stand in about 30 minutes, and they’re available from anywhere. This allows you to spend more time building your boat and less time building your stand. There’s also no need to purchase expensive materials – you can get plastic foam packing blocks for almost nothing!
Styrofoam
If you have an RC boat, you can use surplus Styrofoam blocks to make a stand for it. These are surplus packing materials that ship electronics and other fragile items in cartons. Often, these blocks are discarded along with the cartons. The best way to get them is to look around your local surplus or construction stores. You can also use construction adhesives for Styrofoam wall insulation. These glues set overnight.
When choosing a coating for your styrofoam, choose a low-viscosity one. Resins with low-viscosity are recommended because they cure in thin layers. After an hour, apply a thin layer of the resin and sand it down. Sand it again to even out the surface. Repeat this step if necessary. The resulting material is similar to the thickness of an eggshell. Moreover, this type of foam is more durable and will stand up better to wear.
After trimming the styrofoam, you can start gluing the stand. This makes it easier to determine which part is the bow end. The finished product shows how snug the stand fits around the monohull. In addition, it shows how much clearance is needed for the rudder. A well-made stand for an RC boat is not only stable and functional, but also attractive!
Another option is to use PVC pipe as the frame. PVC plumbing pipe is readily available and connects well with screws, rivets, or adhesives. Make sure to use the correct diameter of the pipe, since smaller ones are likely to bend and flex. You can also use regular PVC cement to make your stand quick and easy. However, if you plan to put a boat on it, you must take this into consideration.
About The Author
Mindy Vu is a part time shoe model and professional mum. She loves to cook and has been proclaimed the best cook in the world by her friends and family. She adores her pet dog Twinkie, and is happily married to her books.