If you’re considering installing a fiberglass pool in your backyard, you should be aware of the time it takes to install. The installation time of a fiberglass pool can vary depending on several factors, including ground conditions, municipality requirements, and the complexity of the product. Fortunately, you can make your installation go as smoothly as possible by learning more about the steps involved in the process. Read on to discover what to expect from the installation process.
Installation time of a fiberglass pool
Getting a fiberglass pool installed requires a minimum of two workers. The pool manufacturer will provide you with the “dig specs” that will ensure a level installation. Once the base material is installed, your pool builder will add the fiberglass pool shell, level it and then set it in place using a crane or excavator. The fiberglass pool shell should then be filled with water, and the entire process should be completed within a few hours.
Depending on the type of fiberglass pool you choose, installation time can vary between one and two days. The exact duration depends on the type of installation and the weather conditions. For example, a new fiberglass pool may require several attempts to prepare the hole, lift the pool level, and add a daylight drain to help balance hydrostatic pressure. While fiberglass pools typically last 40 years if properly installed, they are also challenging to fix. The most common problem that occurs with a fiberglass pool is settled plumbing. Because fiberglass pools are filled 100% with sand, plumbing pipes often sink. A leak may also occur and ruin your yard.
Although fiberglass pools are renowned for their speed of installation, some contractors recommend hiring a contractor for the job. This will save you money and time. Regardless of the style of your fiberglass pool, you should have an experienced contractor do it. A knowledgeable contractor can add stone, tile, brick copings to improve the look of your pool. Installing a fiberglass pool is one of the fastest growing segments in the pool industry in the U.S., and can be installed in any region of the country.
The installation time of a fiberglass pool varies, and you should know your project’s overall timing beforehand. You should also consult with a pool builder who is insured, bonded, and licensed. You want to make sure that the pool is installed correctly to avoid any surprises later on. You should also work with a licensed, bonded, and insured contractor, so you have a legal recourse if your fiberglass pool does not meet your expectations.
Ground conditions
Despite the fact that ground conditions for installing a fiberglass swimming pool are very important, it is a mistake to assume that this type of soil is suitable for installation. In fact, there are certain soil types that do not meet the requirements for installation. Clays and expansive soils, for example, are not suitable for fiberglass pools because of their high water absorption capabilities. Such soils can swell and cause basement and foundation problems. This soil type needs to be replaced with a less-absorbent fill soil. Excessive clay can also increase groundwater pressure under the pool and may negatively affect the pool shell.
To install a fiberglass swimming pool, you should prepare the ground by removing up to 8 inches of backfill around the perimeter of the area. Next, you should drill half-inch holes every 3 feet for rebar installation. Next, place 2′ lengths of 3/8″ rebar in these holes at 90-degree angles. Once the rebar is in place, pour concrete four inches thick around the perimeter of the pool. It is important to work the concrete into the area under the shell’s beam. Afterward, you may drill 3/4″ holes every 36 inches to aid air bleeding.
Another advantage of a fiberglass pool is its ease of installation. Unlike concrete pools, which can take months to complete, a fiberglass pool can be installed in three to six weeks. In some cases, builders are even able to install a fiberglass pool in just a single day. However, the actual installation process may take longer than this depending on the type of equipment used. In either case, it is important to check the ground conditions before installation.
Preparing the site for installation begins with obtaining the necessary permits. You will also have to identify hidden utilities. If any of these utilities interfere with the project, they need to be marked and either abandoned or rerouted. You will also need to prepare the excavation area for the pool. This preparation process takes a couple of hours. Once you have prepared the site, the excavation can begin. Once you are confident in the location, you can start the construction process.
Permit approval time
How long does it take to get a permit for a fiberglass pool? The average time for pool permit approval is between two to six weeks. This time may vary slightly from one municipality to the next. Some municipalities require a site visit, while others prefer to work with electronic files. While there is no set timeframe, the longer the process takes, the more likely it will be that it will take longer than the time frame you were originally quoted.
The length of the permit process depends on where you live. In many areas, the permit process starts before any excavation occurs. This means that you should allot adequate time to complete the permit process. Most of the process is weather dependent, so you should plan accordingly. Your builder will typically handle the permit process, but you will likely need to provide documentation to support your request. Once the permit is acquired, it’s time to begin the construction process.
In many places, municipal authorities vary, and you may have to go through several levels before you can get approved for your project. Check with your homeowners association to determine who to contact. The building department can be found through your builder or homeowners association. Each municipality has its own rules and ordinances. For example, some may require a certain kind of pump or specific spacing between buildings. If you are planning to install a fiberglass pool in your community, you’ll need a permit.
The excavation process starts after you have obtained the necessary permits. After that, you must mark the location of any utilities that will need to be rerouted. The next step is to prepare the excavation area, which will serve as the foundation of your new pool. Preparation time for a fiberglass pool can take anywhere from one to three days, depending on how much work is required. You may want to consult a pool builder if you’re unsure of the permit process.
Permit approval time for a fiberglass pool can vary depending on the size of your project and the location of the property. If you’re building a swimming pool within an RPA, the process can take considerably longer. Be sure to get permits early, especially if you live in an area with wetlands. Remember to apply early, as permit offices don’t receive many requests in the fall and winter. Whether you’re hiring a professional to do the work for you, or handling the process yourself, you must start early. Without a permit, you won’t be able to begin construction.
Quality of installation
You can get an excellent quality pool built on your property with the help of a professional. Usually, you can hire a five-person installation crew to get the job done. Pool installation costs are usually based on the square footage of your property. However, if you are unsure of the installation process, it is better to contact a professional. Listed below are some of the most important considerations to make. In addition to price, consider the time and experience of the pool builder.
A quality fiberglass swimming pool will offer you many advantages. Not only are they easy to install, they are also a quicker alternative to a traditional pool. Moreover, fiberglass swimming pools are fast gaining recognition as a high-quality option. However, you have to be aware that fiberglass pools do have certain disadvantages as well, so you must be prepared to spend more money for them. The good news is that you can get a top-quality fiberglass pool installation if you hire a professional.
If you are planning on constructing a fiberglass pool, the first step is to determine the exact dimensions of the area you are going to use for the pool. Some pools are prefabricated and can be customized to fit a specific area, while others must be custom-built. If you do not want to pay more for a custom installation, you can always add brick or stone copings. Besides, fiberglass pools are one of the fastest growing segments of the pool industry in the U.S.
Another major benefit of choosing a fiberglass pool is that you do not need to worry about resurfacing. Your fiberglass pool will retain its appearance for years. Concrete and vinyl pools will eventually wear out and become stained. Additionally, they require constant chemical additions to keep the pH level in check. This makes fiberglass swimming pools a great investment for your backyard. And since they can be used for many years, you can be sure your investment will increase in value.
The process of fiberglass pool installation takes less time than other types of inground pools. Because they are already manufactured, fiberglass pools require less time to install. Most large inground fiberglass pools take three to six weeks. As long as the pool installer is experienced, the process will go smoothly. In addition, the installation process is much faster with a fiberglass pool than with a concrete one. You won’t need to worry about dealing with contractors who might take too long.
About The Author
Mindy Vu is a part time shoe model and professional mum. She loves to cook and has been proclaimed the best cook in the world by her friends and family. She adores her pet dog Twinkie, and is happily married to her books.